This section lists error codes, names, and messages that are written to the cluster log in the event of transporter errors.
Error Code | Error Name | Error Text |
---|---|---|
0x00 | TE_NO_ERROR | No error |
0x01 | TE_ERROR_CLOSING_SOCKET | Error found during closing of socket |
0x02 | TE_ERROR_IN_SELECT_BEFORE_ACCEPT | Error found before accept. The transporter will retry |
0x03 | TE_INVALID_MESSAGE_LENGTH | Error found in message (invalid message length) |
0x04 | TE_INVALID_CHECKSUM | Error found in message (checksum) |
0x05 | TE_COULD_NOT_CREATE_SOCKET | Error found while creating socket(can't create socket) |
0x06 | TE_COULD_NOT_BIND_SOCKET | Error found while binding server socket |
0x07 | TE_LISTEN_FAILED | Error found while listening to server socket |
0x08 | TE_ACCEPT_RETURN_ERROR | Error found during accept(accept return error) |
0x0b | TE_SHM_DISCONNECT | The remote node has disconnected |
0x0c | TE_SHM_IPC_STAT | Unable to check shm segment |
0x0d | TE_SHM_UNABLE_TO_CREATE_SEGMENT | Unable to create shm segment |
0x0e | TE_SHM_UNABLE_TO_ATTACH_SEGMENT | Unable to attach shm segment |
0x0f | TE_SHM_UNABLE_TO_REMOVE_SEGMENT | Unable to remove shm segment |
0x10 | TE_TOO_SMALL_SIGID | Sig ID too small |
0x11 | TE_TOO_LARGE_SIGID | Sig ID too large |
0x12 | TE_WAIT_STACK_FULL | Wait stack was full |
0x13 | TE_RECEIVE_BUFFER_FULL | Receive buffer was full |
0x14 | TE_SIGNAL_LOST_SEND_BUFFER_FULL | Send buffer was full,and trying to force send fails |
0x15 | TE_SIGNAL_LOST | Send failed for unknown reason(signal lost) |
0x16 | TE_SEND_BUFFER_FULL | The send buffer was full, but sleeping for a while solved |
0x0017 | TE_SCI_LINK_ERROR | There is no link from this node to the switch |
0x18 | TE_SCI_UNABLE_TO_START_SEQUENCE | Could not start a sequence, because system resources are exumed or no sequence has been created |
0x19 | TE_SCI_UNABLE_TO_REMOVE_SEQUENCE | Could not remove a sequence |
0x1a | TE_SCI_UNABLE_TO_CREATE_SEQUENCE | Could not create a sequence, because system resources are exempted. Must reboot |
0x1b | TE_SCI_UNRECOVERABLE_DATA_TFX_ERROR | Tried to send data on redundant link but failed |
0x1c | TE_SCI_CANNOT_INIT_LOCALSEGMENT | Cannot initialize local segment |
0x1d | TE_SCI_CANNOT_MAP_REMOTESEGMENT | Cannot map remote segment |
0x1e | TE_SCI_UNABLE_TO_UNMAP_SEGMENT | Cannot free the resources used by this segment (step 1) |
0x1f | TE_SCI_UNABLE_TO_REMOVE_SEGMENT | Cannot free the resources used by this segment (step 2) |
0x20 | TE_SCI_UNABLE_TO_DISCONNECT_SEGMENT | Cannot disconnect from a remote segment |
0x21 | TE_SHM_IPC_PERMANENT | Shm ipc Permanent error |
0x22 | TE_SCI_UNABLE_TO_CLOSE_CHANNEL | Unable to close the sci channel and the resources allocated |
User Comments
Add your own comment.