Skip navigation links
MySQL 5.0 Reference Manual :: 17 MySQL Cluster :: 17.5 Management of MySQL Cluster :: 17.5.3 Online Backup of MySQL Cluster :: 17.5.3.2 Using The MySQL Cluster Management Client to Create a Backup
17.5.3.3 Configuration for MySQL Cluster Backups »
Section Navigation      [Toggle]

17.5.3.2. Using The MySQL Cluster Management Client to Create a Backup

Before starting a backup, make sure that the cluster is properly configured for performing one. (See Section 17.5.3.3, “Configuration for MySQL Cluster Backups”.)

The START BACKUP command is used to create a backup: 

START BACKUP [backup_id] [wait_option]

wait_option:
WAIT {STARTED | COMPLETED} | NOWAIT

Successive backups are automatically identified sequentially, so the backup_id, an integer greater than or equal to 1, is optional; if it is omitted, the next available value is used. If an existing backup_id value is used, the backup fails with the error Backup failed: file already exists. If used, the backup_id must follow START BACKUP immediately, before any other options are used.

The maximum supported value for backup_id in MySQL 5.0 is 2147483648 (231). (Bug#43042)

Note

If you start a backup using ndb_mgm -e "START BACKUP", the backup_id is required.

The wait_option can be used to determine when control is returned to the management client after a START BACKUP command is issued, as shown in the following list:

  • If NOWAIT is specified, the management client displays a prompt immediately, as seen here: 

    ndb_mgm> START BACKUP NOWAIT
ndb_mgm>

    In this case, the management client can be used even while it prints progress information from the backup process.

  • With WAIT STARTED the management client waits until the backup has started before returning control to the user, as shown here: 

    ndb_mgm> START BACKUP WAIT STARTED
Waiting for started, this may take several minutes
Node 2: Backup 3 started from node 1
ndb_mgm>

  • WAIT COMPLETED causes the management client to wait until the backup process is complete before returning control to the user.

WAIT COMPLETED is the default.

The procedure for creating a backup consists of the following steps:

  1. Start the management client (ndb_mgm), if it not running already.

  2. Execute the START BACKUP command. This produces several lines of output indicating the progress of the backup, as shown here: 

    ndb_mgm> START BACKUP
Waiting for completed, this may take several minutes
Node 2: Backup 1 started from node 1
Node 2: Backup 1 started from node 1 completed
 StartGCP: 177 StopGCP: 180
 #Records: 7362 #LogRecords: 0
 Data: 453648 bytes Log: 0 bytes
ndb_mgm>

  3. When the backup has started the management client displays this message: 

    Backup backup_id started from node node_id

    backup_id is the unique identifier for this particular backup. This identifier is saved in the cluster log, if it has not been configured otherwise. node_id is the identifier of the management server that is coordinating the backup with the data nodes. At this point in the backup process the cluster has received and processed the backup request. It does not mean that the backup has finished. An example of this statement is shown here: 

    	
Node 2: Backup 1 started from node 1

  4. The management client indicates with a message like this one that the backup has started: 

    Backup backup_id started from node node_id completed

    As is the case for the notification that the backup has started, backup_id is the unique identifier for this particular backup, and node_id is the node ID of the management server that is coordinating the backup with the data nodes. This output is accompanied by additional information including relevant global checkpoints, the number of records backed up, and the size of the data, as shown here: 

    	
Node 2: Backup 1 started from node 1 completed
 StartGCP: 177 StopGCP: 180
 #Records: 7362 #LogRecords: 0
 Data: 453648 bytes Log: 0 bytes

It is also possible to perform a backup from the system shell by invoking ndb_mgm with the -e or --execute option, as shown in this example: 

shell> ndb_mgm -e "START BACKUP 6 WAIT COMPLETED"

When using START BACKUP in this way, you must specify the backup ID.

Cluster backups are created by default in the BACKUP subdirectory of the DataDir on each data node. This can be overridden for one or more data nodes individually, or for all cluster data nodes in the config.ini file using the BackupDataDir configuration parameter as discussed in Identifying Data Nodes. The backup files created for a backup with a given backup_id are stored in a subdirectory named BACKUP-backup_id in the backup directory.

To abort a backup that is already in progress:

  1. Start the management client.

  2. Execute this command: 

    ndb_mgm> ABORT BACKUP backup_id

    The number backup_id is the identifier of the backup that was included in the response of the management client when the backup was started (in the message Backup backup_id started from node management_node_id).

  3. The management client will acknowledge the abort request with Abort of backup backup_id ordered.

    Note

    At this point, the management client has not yet received a response from the cluster data nodes to this request, and the backup has not yet actually been aborted.

  4. After the backup has been aborted, the management client will report this fact in a manner similar to what is shown here: 

    Node 1: Backup 3 started from 5 has been aborted. Error: 1321 - Backup aborted by user request: Permanent error: User defined error
Node 3: Backup 3 started from 5 has been aborted. Error: 1323 - 1323: Permanent error: Internal error
Node 2: Backup 3 started from 5 has been aborted. Error: 1323 - 1323: Permanent error: Internal error
Node 4: Backup 3 started from 5 has been aborted. Error: 1323 - 1323: Permanent error: Internal error

    In this example, we have shown sample output for a cluster with 4 data nodes, where the sequence number of the backup to be aborted is 3, and the management node to which the cluster management client is connected has the node ID 5. The first node to complete its part in aborting the backup reports that the reason for the abort was due to a request by the user. (The remaining nodes report that the backup was aborted due to an unspecified internal error.)

    Note

    There is no guarantee that the cluster nodes respond to an ABORT BACKUP command in any particular order.

    The Backup backup_id started from node management_node_id has been aborted messages mean that the backup has been terminated and that all files relating to this backup have been removed from the cluster file system.

It is also possible to abort a backup in progress from a system shell using this command: 

shell> ndb_mgm -e "ABORT BACKUP backup_id"

Note

If there is no backup having the ID backup_id running when an ABORT BACKUP is issued, the management client makes no response, nor is it indicated in the cluster log that an invalid abort command was sent.