- Documentation Library
- Table of Contents
- MySQL 5.5 Manual
- MySQL 5.4 Manual
- MySQL 5.1 Manual
- MySQL 5.0 Manual
- MySQL 3.23/4.0/4.1 Manual
- Table of Contents
- A.5.2 Common Errors When Using MySQL Programs
- A.5.2.1 Access denied
- A.5.2.2 Can't connect to [local] MySQL server
- A.5.2.3 Lost connection to MySQL server
- A.5.2.4 Client does not support authentication protocol
- A.5.2.5 Password Fails When Entered Interactively
- A.5.2.6 Host 'host_name' is blocked
- A.5.2.7 Too many connections
- A.5.2.8 Out of memory
- A.5.2.9 MySQL server has gone away
- A.5.2.10 Packet too large
- A.5.2.11 Communication Errors and Aborted Connections
- A.5.2.12 The table is full
- A.5.2.13 Can't create/write to file
- A.5.2.14 Commands out of sync
- A.5.2.15 Ignoring user
- A.5.2.16 Table 'tbl_name' doesn't exist
- A.5.2.17 Can't initialize character set
- A.5.2.18 'File' Not Found and Similar Errors
- A.5.2.19 Table-Corruption Issues
The server error log can be a useful source of information
about connection problems. See Section 5.3.1, “The Error Log”.
Starting with MySQL 3.23.40, if you start the server with the
--warnings
option (or --log-warnings from
MySQL 4.0.3 on), you might find messages like this in your
error log:
010301 14:38:23 Aborted connection 854 to db: 'users' user: 'josh'
If a client successfully connects but later disconnects
improperly or is terminated, the server increments the
Aborted_clients status
variable, and logs an Aborted
connection message to the error log. The cause can
be any of the following:
The client program did not call
mysql_close()before exiting.The client had been sleeping more than
wait_timeoutorinteractive_timeoutseconds without issuing any requests to the server. See Section 5.1.3, “Server System Variables”.The client program ended abruptly in the middle of a data transfer.
If a client is unable even to connect, the server increments
the Aborted_connects status
variable. Unsuccessful connect attempts can occur for the
following reasons:
A client doesn't have privileges to connect to a database.
A client uses an incorrect password.
A connection packet doesn't contain the right information.
It takes more than
connect_timeoutseconds to get a connect packet. See Section 5.1.3, “Server System Variables”.
If these kinds of things happen, it might indicate that someone is trying to break into your server! Messages for these types of problems are logged to the general query log if it is enabled.
MySQL Enterprise.
For reasons of security and performance the advisors
provided by the MySQL Enterprise Monitor pay special
attention to the Aborted_connects status
variable. For more information, see
http://www.mysql.com/products/enterprise/advisors.html.
Other reasons for problems with aborted clients or aborted connections:
Use of Ethernet protocol with Linux, both half and full duplex. Many Linux Ethernet drivers have this bug. You should test for this bug by transferring a huge file via FTP between the client and server machines. If a transfer goes in burst-pause-burst-pause mode, you are experiencing a Linux duplex syndrome. The only solution is switching the duplex mode for both your network card and hub/switch to either full duplex or to half duplex and testing the results to determine the best setting.
Some problem with the thread library that causes interrupts on reads.
Badly configured TCP/IP.
Faulty Ethernets, hubs, switches, cables, and so forth. This can be diagnosed properly only by replacing hardware.
The
max_allowed_packetvariable value is too small or queries require more memory than you have allocated for mysqld. See Section A.5.2.10, “Packet too large”.
User Comments
Add your own comment.