#
# NetWorker
# 7.2.2.Build.422
# LEGATO Software, a division of EMC.
#
# ATL ASC/ASCQ Error Codes
#
0x80, 0x00, door is open, inventory may have been corrupted
0x80, 0x01, transfer full - gripper has cartridge in it
0x80, 0x06, transfer empty - command aborted
0x80, 0x07, system stopped - stop button on panel was pressed
0x80, 0x08, logical unit turned on-line - press standby button
0x80, 0x09, logical unit turned off-line (diag mode)
0x80, 0x10, load retry failed
0x80, 0x0a, nvram checksum failure
0x80, 0x0b, command aborted by user
0x80, 0x0d, cartridge is only partially gripped
0x80, 0x0e, data transfer changed
0x80, 0x0f, low power error
0x80, 0x11, motor power failure
0x80, 0x22, element contents unknown
0x80, 0x23, barcode decoder communication failure
0x81, 0x00, gripper axis internal fail
0x81, 0x01, gripper timeout
0x81, 0x04, gripper open failure
0x81, 0x05, gripper close failure
0x81, 0x51, unable to pick cartridge
0x81, 0x54, gripper tpu register failure
0x81, 0x55, gripper tpu ram failure
0x82, 0x00, rotary axis internal failure
0x82, 0x01, rotary timeout
0x82, 0x04, rotary front failed
0x82, 0x05, rotary back failed
0x82, 0x08, rotary home not found
0x82, 0x10, rotary invalid start
0x82, 0x11, rotary invalid command
0x82, 0x20, rotary test failure
0x82, 0x23, rotary position overflow
0x83, 0x00, extension internal failure
0x83, 0x01, extension timeout
0x83, 0x02, extension current feedback failure
0x83, 0x03, extension mechanical position error
0x83, 0x08, extension home not found
0x83, 0x10, extension invalid actuator start position
0x83, 0x11, extension invalid command
0x83, 0x20, extension test failure
0x83, 0x22, extension encoder failure
0x83, 0x40, extension force not reached
0x83, 0x41, extension force object missing
0x83, 0x50, extension sensor failure
0x84, 0x00, vertical internal failure
0x84, 0x01, vertical timeout
0x84, 0x03, vertical mechnical position error
0x84, 0x08, vertical home not found
0x84, 0x10, vertical invalid actuator start position
0x84, 0x11, vertical invalid command
0x84, 0x20, vertical test failure
0x84, 0x22, vertical encoder failure
0x84, 0x23, vertical position overflow
0x84, 0x30, vertical mapping failure
0x85, 0x00, horizontal internal failure
0x84, 0x01, horizontal timeout
0x85, 0x03, horizontal mechnical position error
0x85, 0x08, horizontal home not found
0x85, 0x10, horizontal invalid actuator start position
0x85, 0x11, horizontal invalid command
0x85, 0x20, horizontal test failure
0x85, 0x22, horizontal encoder failure
0x85, 0x23, horizontal position overflow
0x85, 0x30, horizontal mapping failure
0x88, 0x00, warning safe temperature exceeded
0x88, 0x01, maximum temperature exceeded
0x8a, 0x02, uncalibrated position
0x8c, 0x01, load port timeout
0x8c, 0x06, load pack detent failure
0x8d, 0x01, drive handle timeout
0x8d, 0x24, drive handle hardware failure
0x8e, 0x01, flash memory unable to identify
0x8e, 0x02, flash memory unable to erase
0x8e, 0x03, flash memory unable to program
0x8f, 0x00, library command timeout
0xf0, 0x01, reservation conflict
0xf1, 0x00, command unspecified
0xf1, 0x01, command heap overflow
0xf1, 0x02, command unrecognized
0xf1, 0x03, command register error
0xf3, 0x00, drive communication internal failure
0xf3, 0x02, drive communication timeout
0xf3, 0x11, drive handle not ok
