Patch-ID# 109082-05 Keywords: desktop standalone flash prom update Synopsis: Hardware/PROM: Ultra 80 & E420R Standalone Flash PROM Update Date: Sep/10/2001 *********************************************************** Patch 109082-05 was re-instated on Dec 4, 2003. Reason: Pathc 109082-06 has been withdrawn due to: Bug found with register change for Micron DIMMs in OBP 3.33. The changes do not work well with 2 CPUs and 2 GB DIMM configurations. For further information, please refernce bug ID4963249. Recommendation: Please backout patch 109082-06 and re-install patch 109082-05. *********************************************************** Install Requirements: None Solaris Release: 7 8 SunOS Release: 5.7 5.8 Unbundled Product: Hardware/PROM NOTE: This utility is *not* OS-dependent. The list of releases shown under the "Solaris Release" and "SunOS Release" sections may not be complete: The absence of a valid Solaris Release or SunOS Release from the lists above does not preclude the installation of this patch against the hardware. Unbundled Release: OBP_3.31.0,POST_1.2.8,OBDIAG_1.0 Xref: Topic: Relevant Architectures: sparc NOTE: sun4u ultra 80 & e420r only BugId's fixed with this patch: 4123985 4176300 4203447 4256699 4287319 4310258 4318271 4325933 4338343 4346332 4360786 4360814 4360883 4407855 4407869 4416722 4421857 4483753 4484524 Changes incorporated in this version: 4484524, 4416722, 4421857, 4483753 Patches accumulated and obsoleted by this patch: Patches which conflict with this patch: Patches required with this patch: Obsoleted by: Files included with this patch: 802-3233-20.ps, flash-update-Ultra80-05, flash-update-Ultra80-01, copyright flash-update-Ultra80-02, flash-update-Ultra80-03, flash-update-Ultra80-04, flash-update-Ultra80-latest, README.109082-05, Problem Description: BugId 4484524: Add support for mirrored SRAM modules which identify themselves BugId 4416722: Ultra-60/80 OBP slot-names property for pci devices is wrong BugId 4421857: Ultra 80 do not conform to PCI2.2 T(rhfa) timing BugId 4483753: RARP replies which dont include ar$spa must be handled correctly BugId 4407855: Code that validates idprom contents incorrectly expects 0x80 at offset 1 BugId 4407869: probe-scsi and probe-scsi-all need to recognize device_type=scsi* Bugid 4360814: PCI resources allocated on one segment is not available on the other Bugid 4318271: During probe register at 0x30 not found on Ultra 10 Bugid 4360786: Ecache sizing may be incorrect on modules using IBM SRAM parts Bugid 4360883: DHCP IP address validation code must be more robust Bugid 4123985: erroneous divide by zero bug in OBP Bugid 4325933: Branch on register intructions are broken in assem.fth Bugid 4338343: fb8: "Memory Address not Aligned" error in fb8-insert-lines Bugid 4176300: Draw logo doesn't clip, returns negative number for line# to draw at. Bugid 4203447: setting nvram variables when config-valid? is false leaves parameters on stack Bugid 4346332: System type is not displayed in banner after flash update Bugid 4310258: Add support for DHCP. Bugid 4287319: The flash utility needs to be able to support ST and Hyundai 29F080 parts. Bugid 4256699: Ultra 60s/450 mhz cpus fail jumpstart install even with OE CD modification. Patch Installation Instructions: ================================ Intro ----- This README is intended for users who wish to upgrade the firmware in their Ultra 80 or E420R system Flash PROM. Summary of the Patch Installation Process: ------------------------------------------ The installation shall comprise of the following steps 1) Determine the system's current Flash PROM firmware revision. 2) Compare the current Flash PROM firmware revision with the available or latest Flash PROM firmware revisions. 3) If the current Flash PROM firmware revision is lower than the latest available firmware revision in this patch, then proceed to the next step. If NOT, STOP: DO NOT CONTINUE. 4) Prepare the system for the Flash PROM update 5) Running the Flash PROM Utility 6) Verifying successful Flash PROM Update 7) Restoring the system 8) Resume operations Patch Installation instructions (in detail): ============================================ The required steps are explained in greater detail below. 1) Determine the System's Current Firmware Revisions ------------------------------------------------- While the OS is running the following command may be used to determine the current system firmware revisions; /usr/sbin/prtconf -V or /usr/platform/sun4u/sbin/prtdiag -v | grep OBP The firmware revisions may also be determined from the PROM monitor's "ok" prompt with the following command; .version 2) Compare the current Flash PROM firmware revision with the available or latest Flash PROM firmware revisions. Compare the output of the OBP line in the "prtdiag -v" or "prtconf -V" output. Find the revision number and compare with the revision on the entries below that of the "flash-update-Ultra80-latest" line Available Firmware Revisions ---------------------------- -01 flash-update-Ultra80-01 OBP: 3.23 Version 0 created 1999/06/30 13:53 POST: 1.2.7 1999/05/24 17:33 -02 flash-update-Ultra80-02 OBP: 3.25 Version 0 created 1999/12/03 11:29 POST: 1.2.7 1999/05/24 17:33 -03 flash-update-Ultra80-03 OBP: UPA/PCI 3.27 Version 0 created 2000/08/23 15:41 POST: 1.2.8 08/22/2000 07:50 PM -04 flash-update-Ultra80-04 OBP: UPA/PCI 3.29 Version 0 created 2000/12/20 18:40 POST: 1.2.8 08/22/2000 07:50 PM -LATEST flash-update-Ultra80-05; flash-update-Ultra80-latest OBP: UPA/PCI 3.31 Version 0 created 2001/07/25 20:35 POST: 1.2.8 08/22/2000 07:50 PM 3) Is the UPGRADE NECESSARY? If the current Flash PROM revision matches the version numbers given under the flash-update-Ultra80-latest line, then STOP Here. This UPGRADE IS NOT NECESSARY. If the current Flash PROM firmware revision is lower than the latest firmware revision in this patch, then proceed to the next step. 4) Preparing the System --------------------- a) As root, copy the latest "flash-update" files from the directory containing the patch to the root directory as follows: # cp flash*latest / # chmod 755 /flash-update* In order to boot the binary, it must be located within the root partition. If it is not already located within the root partition then move it to /. If the binary is already located elsewhere within the root partition then note the exact filepath so that the binary can be booted later. b) As root, exit the OS such that the system returns to the PROM's "ok" prompt: # halt ok c) Power off the system. ** CAUTION ** Do not attempt to access any part of the system hardware with the system power still on! d) Remove the system top cover. (If you are unsure how to do this then consult your system "Installation Guide" or "Service Manual".) e) Set J3001 to write enable at 2+3. Default is write protect at 1+2 Locate jumper J3001. NOTE that a plug-in card may be installed in the system which covers J3001 - if this is the case then you will have to remove the plug-in card in order to access J3001. Jumper J3001 provides a write enable/disable mechanism for the Flash PROM. J3001 normally connects pins 1+2, which causes the Flash PROM to be write protected. To enable patch installation, write enable the Flash PROM by MOVING the J3001 jumper from pins 1+2 to pins 2+3. **IMPORTANT NOTE**: If this jumper is NOT set to WRITE ENABLE, the Flash update will fail. (If you have difficulty locating J3001 then consult Figure 1-6 in the "Sun Flash PROM Guide for Workstations and Workgroup Servers - Standalone Version"). If a plug-in card was removed to access J3001 in the step above then reinstall the card now. f) Replace the system top cover. 5) Running the Flash Update Utility -------------------------------- a) Power on the system Wait for the PROM's banner to appear, and then b) Use the Stop-A keys (or Break key, if running from a serial line) to abort the auto-boot sequence. ** NOTE ** If the flash update completes normally then the values contained within the system's Non-Volatile RAM (NVRAM) configuration variables will be retained. However, if the update process is some- how interrupted then it is possible that any non-default values contained in NVRAM will be lost. For this reason it is recommended that you note down on paper the contents of any NVRAM configuration variable which has been customized so that they may be manually restored at a later time, if necessary. (Use the PROM's "printenv" command to list the variables and their values.) c) The system should now display the PROM monitor's "ok" prompt. Now boot the Flash update utility as given below: CAUTION: Do not boot/run revisions lower than the latest unless you are absolutely sure that that is what you want to do! ok boot disk /flash-update-Ultra80-latest NOTE: If your system's boot device is not "disk" then you will have to specify the appropriate devalias (e.g. disk2). If the binary is located in a location other than / then provide the entire filepath after the boot device. Answer the questions as prompted by the utility. +++++++++++++++++++++ example Flash update follows ++++++++++++++++++++++++ ++++++++ Note that this is an example only. Much of the information ++++++ ++++++++ which is displayed by your system will be different from ++++++ ++++++++ what is shown below. ++++++ +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ Standalone Flash PROM Update Utility, Rev. 2.4 Ultra(tm) 1 Ultra(tm) 2 Ultra(tm) 5/10 Ultra(tm) 30 Ultra(tm) 60 / E220R Ultra(tm) 80 / E420R Ultra(tm) Enterprise(tm) 250 Ultra(tm) Enterprise(tm) 450 This utility allows you to interactively update the firmware revisions in specific system Flash PROM components. Type h for help, q to quit, Return or Enter to continue: Every precaution should be taken to prevent the loss of system power during the Flash PROM programming process! Type h for help, q to quit, Return or Enter to continue: Firmware Release(s) Firmware Release(s) Currently Existing in the System Available for Installation / Install? ---------------------------------- ------------------------------------------- OBP 3.1.2 1996/03/28 17:08 OBP 3.1.5 1996/08/27 16:13 no POST 3.1.4 1996/04/09 03:23 POST 3.1.5 1996/06/28 11:54 no Type sa if you wish to select all available firmware releases for installation. Type h for help, quit to exit, or cont to continue: sa Firmware Release(s) Firmware Release(s) Currently Existing in the System Available for Installation / Install? ---------------------------------- ------------------------------------------- OBP 3.1.2 1996/03/28 17:08 OBP 3.1.5 1996/08/27 16:13 YES POST 3.1.4 1996/04/09 03:23 POST 3.1.5 1996/06/28 11:54 YES Type sa if you wish to select all available firmware releases for installation. Type h for help, quit to exit, or cont to continue: cont The Flash programming process is about to begin. Type h for help, q to quit, Return or Enter to continue: Erasing the top half of the Flash PROM. Programming OBP into the top half of the Flash PROM. Verifying OBP in the top half of the Flash PROM. Erasing the bottom half of the Flash PROM. Programming OBP into the bottom half of Flash PROM. Verifying OBP in the bottom half of the Flash PROM. Erasing the top half of the Flash PROM. Programming POST into the top half of Flash PROM. Verifying POST in the top half of the Flash PROM. Programming was successful. Resetting ... Restoring previous NVRAM environment settings... #power-cycles = 10 auto-boot? = false security-#badlogins = 0 OK Resetting ... +++++++++++++++++++++ example Flash update ends ++++++++++++++++++++++++++ Note that the section "Restoring previous NVRAM environment settings..." up to the "Resetting ..." line will only be displayed on serial port A. If you are running from the keyboard/console devices then you will not see those lines displayed. Once the PROM's banner reappears then use the Stop-A keys (or Break key, if running from a serial line) to abort the auto-boot sequence if the system begins to boot. 6) Verifying successful Flash PROM Update Verify from the results of the .version command that the OBP version matches the OBP version given above under the flash-update-Ultra80-latest entry in Step 2. 7) Restoring the system The system should be restored to the original set-up as follows: a) Turn the power to the system off. b) Remove the top cover and move jumper J3001 to pins 1+2. c) Replace the top cover. If any problems should be encountered during the firmware upgrade then consult the "Sun Flash PROM Guide for Workstations and Workgroup Servers - Standalone Version". 8) Resume operations a) Turn on the system power and allow the system to boot the operating system. b) Once the system has rebooted you may wish to remove the Flash Update binaries and documents since they will no longer be needed. # rm /flash-update* c) Remember to remove the files from their original location if they were not extracted directly into the root directory. Special Install Instructions: ----------------------------- ************************************************************************** ************************************************************************** **WARNING:****WARNING:****WARNING:****WARNING:****WARNING:****WARNING:** * PLEASE READ THE INSTRUCTIONS CAREFULLY AND ENTIRELY. PLEASE FOLLOW THE INSTRUCTIONS EXACTLY AS THEY ARE STATED. * FAILURE TO FOLLOW INSTRUCTIONS COULD EITHER RESULT IN A DEFECTIVE BOARD OR UNSUCCESSFUL FLASH PROM UPDATE. * THIS IS NOT A STANDARD PATCH in that it does not use the installpatch and backoutpatch scripts. * THIS PATCH CANNOT BE INSTALLED ON AN ONLINE OPERATING SYSTEM BECAUSE THE INSTALL INSTRUCTIONS REQUIRES THAT THE SYSTEM BE BROUGHT DOWN. BE SURE TO SCHEDULE DOWN TIME TO INSTALL THIS PATCH. * INSTALLATION OF THIS PATCH REQUIRES A HARDWARE JUMPER CHANGE. IF YOU ARE UNSURE ON HOW TO OPEN THE SYSTEM BOX, PLEASE ENSURE THAT A QUALIFIED PERSON, WITH THE STATIC WRIST STRAP KIT NEEDED TO SERVICE ELECTRONIC EQUIPMENT, IS AVAILABLE TO COMPLETE THIS ACTIVITY. FAILURE TO USE STATIC PROTECTION KIT OR IMPROPER HANDLING COULD RESULT IN THE DAMAGE OF THE SYSTEM BOARD. * PLEASE REVIEW NOT ONLY THIS README BUT ALSO ADDITIONAL DOCUMENTATION GIVEN. The file "802-3233-xx.ps" where xx stands for the latest numeric revision is a PostScript copy of the "Sun Flash PROM Guide for Workstations and Workgroup Servers - Standalone Version", which provides the following; (i) A board-level diagram that gives the approximate location of the hardware jumpers (that will need to be changed). (ii) Emergency instructions in the unlikely event that the Flash update should fail. Note, however, that The Flash PROM Guide was originally written for a user who is running the Flash PROM update utility from a bootable CDROM, and thus it will not contain the proper boot commands for installation of this patch. Also note that the instructions in the document for installing packages are not valid for this patch. **WARNING:****WARNING:****WARNING:****WARNING:****WARNING:****WARNING:** ************************************************************************** ************************************************************************** README -- Last modified date: Thursday, December 4, 2003